M306NKT-EPBEmulation Probe for M16C/6N Group M16C/6NK, 6NL, 6NM, 6NN, 6N4, 6N5User’s ManualRev.1.00 July 16, 2004 REJ10J0519-0100Z
( 10 / 74 ) CAUTION Note on Connecting a Power Supply of the Emulator: z Do not modify this product. Modifying or disassembling this product wil
Chapter 1. Precautions for Safety ( 11 / 74 ) IMPORTANT Notes on Downloading Firmware: z Before using this product for the first time, it is necessa
( 12 / 74 ) IMPORTANT Note on RDY* Input: z Be sure to input a low to pin RDY* of the user system during the user program execution (only while the
Chapter 1. Precautions for Safety ( 13 / 74 ) IMPORTANT Notes on Reset Vector Area: z Memory in the emulator main unit is always selected as a reset
( 14 / 74 ) IMPORTANT Note on Breaks: z The area displaying break points in the program window of the emulator debugger shows the following breaks.
Chapter 1. Precautions for Safety ( 15 / 74 ) IMPORTANT Note on Differences between the Actual MCU and Emulator: z Operations of the emulator system
( 16 / 74 ) IMPORTANT Notes on Pullup Control: z Because this product emulates some I/O ports (P0 to P5, P10), you can not pullup ports P0 to P5 by
Chapter 1. Precautions for Safety ( 17 / 74 ) IMPORTANT Notes on Debugging in CPU Rewrite Mode: z When you debug the M16C/6N Group M16C/6NK, M16C/6N
( 18 / 74 ) MEMO
Chapter 2. Preparation ( 19 / 74 ) Chapter 2. Preparation This chapter describes the package components, the system configuration and the preparat
( 2 / 74 ) * IC61-1004-051 is a trademark of Yamaichi Electronics Co., Ltd. * NQPACK, YQPACK, YQSOCKET, YQ-GUIDE, HQPACK, TQPACK and TQSOCKET are tra
( 20 / 74 ) 2.1 Package Components The M306NKT-EPB package consists of the following items. When unpacking it, check to see if your M306NKT-EPB cont
Chapter 2. Preparation ( 21 / 74 ) 2.3 Name of Each Part 2.3.1 System Configuration Figure 2.1 shows a configuration of the PC7501 system. Figure 2.
( 22 / 74 ) 2.3.2 Names and Functions of the PC7501 Upper Panel LEDs Figure 2.2 shows the names of the LEDs on the upper panel of the PC7501. Fi
Chapter 2. Preparation ( 23 / 74 ) (2) Target Status LEDs The target status LEDs indicate operating status of the target MCU and power supply of the
( 24 / 74 ) 2.4 When Using the Emulator for the First Time 2.4.1 Downloading Firmware If you have purchased this emulation probe newly, you need to
Chapter 3. Setup ( 25 / 74 ) Chapter 3. Setup This chapter describes switch settings required for using this product and how to connect this produ
( 26 / 74 ) 3.1 Selecting Clock Supply 3.1.1 Clocks You can choose a clock supplied to the evaluation MCU by the Emulator tab in the Init dialog box
Chapter 3. Setup ( 27 / 74 ) 2. Replace the oscillator circuit board (see Figure 3.2). The oscillator circuit board of the PC7501 is in the lower
( 28 / 74 ) (3) Using the Internal Oscillator Circuit Bare Board To use the emulation probe at a frequency you like, build a desired oscillator circ
Chapter 3. Setup ( 29 / 74 ) 3.1.3 Using the Oscillator Circuit on the User System To operate this product with an external clock, construct the osci
( 3/ 74 ) Preface The M306NKT-EPB is an emulation probe for the M16C/6N Group M16C/6NK, M16C/6NL, M16C/6NM, M16C/6NN, M16C/6N4, M16C/6N5 MCUs. The M
( 30 / 74 ) 3.1.4 Using the Internal Generator Circuit The dedicated circuit in the PC7501 can generate any arbitrary frequency specified by the emu
Chapter 3. Setup ( 31 / 74 ) 3.2 A-D Conversion Bypass Capacitors There is a foot pattern on the M306NKT-EPBM board for mounting bypass capacitors fo
( 32 / 74 ) 3.3 Pullup of Emulation Ports Because this product emulates some I/O ports (P0 to P5, P10), you can not pullup ports P0 to P5 by the pul
Chapter 3. Setup ( 33 / 74 ) 3.4 Connecting the PC7501 Figure 3.9 shows how to connect the PC7501 and the emulation probe. Figure 3.9 Connecting the
( 34 / 74 ) 3.5 Connecting the User System (M16C/6N4, /6N5) Figure 3.10 shows how to connect this product according to your user system. Figure 3.1
Chapter 3. Setup ( 35 / 74 ) 3.5.1 Connecting to a 100-pin LCC Socket Here following is a procedure of connecting to a 100-pin LCC socket (IC61-1004-
( 36 / 74 ) 3.5.2 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1) Here following is a procedure of connecting to a 100-pin 0.65-mm-pitch
Chapter 3. Setup ( 37 / 74 ) 3.5.3 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 2) Here following is a procedure of connecting to a 100-p
( 38 / 74 ) 3.5.4 Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 3) Here following is a procedure of connecting to a 100-pin 0.65-mm-pitch
Chapter 3. Setup ( 39 / 74 ) 3.6 Connecting the User System (M16C/6NK, /6NL, /6NM, /6NN) Figure 3.15 shows how to connect this product according to y
( 4 / 74 ) Contents Chapter 1. Precautions for Safety ...
( 40 / 74 ) 3.6.1 Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 1) Here following is a procedure of connecting to a 100-pin 0.5-mm-pitch f
Chapter 3. Setup ( 41 / 74 ) 3.6.2 Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 2) Here following is a procedure of connecting to a 100-pi
( 42 / 74 ) 3.6.3 Connecting to a 100-pin 0.5-mm-pitch Foot Pattern (Part 3) Here following is a procedure of connecting to a 100-pin 0.5-mm-pitch f
Chapter 3. Setup ( 43 / 74 ) 3.6.4 Connecting to a 128-pin 0.5-mm-pitch Foot Pattern Here following is a procedure of connecting to a 128-pin 0.5-mm-
( 44 / 74 ) MEMO
Chapter 4. Usage ( 45 / 74 ) Chapter 4. Usage This chapter describes from turning on the power of this product to starting up the emulator debugge
( 46 / 74 ) 4.1 Turning On the Power 4.1.1 Checking Connections of the Emulator System Before turning the power ON, check the connection of the inte
Chapter 4. Usage ( 47 / 74 ) 4.1.4 LED Display When the PC7501 Starts Up Normally Figure 4.1 shows upper panel LED lighting status when the emulator
( 48 / 74 ) 4.2 Downloading Firmware 4.2.1 When It is Necessary to Download Firmware It is necessary to download the firmware in the cases listed be
Chapter 4. Usage ( 49 / 74 ) 4.3 Self-check 4.3.1 Self-check Procedure To run the self-check of the emulator, do so as explained here below. While th
Chapter 1. Precautions for Safety ( 5 / 74 ) 2.4 When Using the Emulator for the First Time ...
( 50 / 74 ) 4.3.2 If an Error is Detected in the Self-check If the self-check does not result normally (ERROR 1 to ERROR 4 in Figure 4.3), check the
Chapter 5. Specifications ( 51 / 74 ) Chapter 5. Specifications This chapter describes specifications of this product. 5.1 Specifications ...
( 52 / 74 ) 5.1 Specifications Table 5.1 Specifications of the M306NKT-EPB Emulator PC7501 Applicable MCU M16C/6N Group M16C/6NK, M16C/6NL, M16C/6
Chapter 5. Specifications ( 53 / 74 ) Vcc=5V 5.2 Operation Timing of Memory Expansion Mode and Microprocessor Mode (5 V) (1) Separate Bus Timing Tab
( 54 / 74 ) Vcc=5V Figure 5.1 Memory expansion mode and microprocessor mode (3-wait, accessing external area) ReadWriteBCLKCSiADiBHEALERDDBitd(BCL
Chapter 5. Specifications ( 55 / 74 ) Vcc=5V (2) Multiplex Bus Timing Table 5.3 and Figure 5.2 show the bus timing in memory expansion mode and micr
( 56 / 74 ) Vcc=5V Figure 5.2 Memory expansion mode and microprocessor mode (2-wait, accessing external area, using multiplex bus) ReadWriteBCLKCS
Chapter 5. Specifications ( 57 / 74 ) Vcc=5V (3) Timing Requirements Tables 5.4 and Figure 5.3 list the timing requirements. Table 5.4 Timing requir
( 58 / 74 ) 5.3 Connection Diagram Figures 5.4 shows a connection diagram of the M306NKT-EPB. This connection diagram mainly shows the interface sec
Chapter 5. Specifications ( 59 / 74 ) Table 5.5 Electrical characteristics of 74HC4066 Standard values Symbol Item Condition Min. Standard Max. Unit
( 6 / 74 ) Terminology Some specific words used in this user's manual are defined as follows: PC7501 system This means an emulator system buil
( 60 / 74 ) 5.4 External Dimensions 5.4.1 External Dimensions of the Emulation Probe Figure 5.5 shows external dimensions of the M306NKT-EPB and M30
Chapter 5. Specifications ( 61 / 74 ) 5.4.2 External Dimensions of the Converter Board M30800T-PTC Figure 5.6 shows external dimensions of the conver
( 62 / 74 ) 5.4.3 External Dimensions of the Converter Board M3T-F160-100NSD Figure 5.7 shows external dimensions and a sample foot pattern of the c
Chapter 6. Troubleshooting ( 63 / 74 ) Chapter 6. Troubleshooting This chapter describes how to troubleshoot when this product does not work prope
( 64 / 74 ) 6.1 Flowchart to Remedy the Troubles Figure 6.1 shows the flowchart to remedy the troubles from when power to the emulator is activated
Chapter 6. Troubleshooting ( 65 / 74 ) 6.2 When the Emulator Debugger Does Not Start Up Properly (1) When the LEDs of the PC7501 Shows an Error Tabl
( 66 / 74 ) (2) MCU Setting Dialog Box Does Not Appear at Debugger Startup (target connected) Table 6.2 Checkpoints of errors at debugger startup (
Chapter 6. Troubleshooting ( 67 / 74 ) (3) MCU Setting Dialog Box Does Not Appear at Debugger Startup (target not connected) Table 6.3 Checkpoints o
( 68 / 74 ) MEMO
Chapter 7. Maintenance and Guarantee ( 69 / 74 ) Chapter 7. Maintenance and Guarantee This chapter describes how to maintenance, repair provisions
Chapter 1. Precautions for Safety ( 7 / 74 ) Chapter 1. Precautions for Safety This chapter describes precautions for using this product safely an
( 70 / 74 ) 7.1 Maintenance If dust or dirt collects on any equipment of your emulation system, wipe it off with a dry soft cloth. Do not use thinne
Chapter 7. Maintenance and Guarantee ( 71 / 74 ) 7.4 How to Make Request for Repair If your product is found faulty, follow the procedure below to se
( 72 / 74 ) MEMO
M306NKT-EPB User’s Manual Rev.1.00 July 16, 2004 REJ10J0519-0100Z COPYRIGHT ©2004 RENESAS TECHNOLOGY CORPORATION AND RENESAS SOLUTIONS CORPORATIO
( 8 / 74 ) 1.1 Safety Symbols and Meanings In both the user's manual and on the product itself, several icons are used to insure proper handlin
Chapter 1. Precautions for Safety ( 9 / 74 ) WARNING Warning for Installation: z Do not set this product in water or areas of high humidity. Make
Comments to this Manuals