To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C
i Preface Thank you for purchasing this user system interface cable (HS2212ECH61H) for the Hitachi’s original microcomputer H8S/2212 Series. The HS22
ii Contents Section 1 Configuration...1 Section 2 Connection P
Section 1 Configuration CAUTION Use an IC149-064-175-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-64E package I
2 Table 1 lists the HS2212ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2212ECH61H Components No.
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below. F
Emulator stationCable body connectorScrews for fixingthe cable bodyUser system interface cableE6000 Figure 2 Connecting User System Interface Cable
2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER S
6 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a FP-64E package on the use
Pin 1Cable headIC socket (IC149-064-175-B51manufactured by YAMAICHI ELECTRONICS Co., Ltd.)Screws (M2 x 12 mm)with flat washersUser system Figure 3 C
2.2.5 Fastening Cable Body Connect the cable body to the cable head. 8 Cable bodyCable headRemove jigPush the remove jigUser systemRemoving Figure 4
Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. Unit: m
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head
12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver
Pin 1IC socket (IC149-064-175-B51manufactured by YAMAICHI ELECTRONICS Co., Ltd.)User systemScrews (M2 x 6 mm)with flat washersSocket coverMCU Figure 8
Section 4 User Interface Circuit The user system interface cable includes the H8S/2218 microcomputer to emulate the USB function. The H8S/2212 user
Section 5 Verifying Operation 1. When using the H8S/2214 E6000 emulator for the H8S/2212 Series, turn on the emulator according to the procedures d
Section 6 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable
17 7. In the H8S/2212 series, the USB control register and the RTC control register are allocated to external bus areas of area 6 (H’C00000 to H’DFF
I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy
II LIMITED WARRANTY Hitachi warrants its user system interface cables to be manufactured in accordance with published specifications and f
III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,
SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future re
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulato
H8S/2212 Series FP-64EUser System Interface Cable(HS2212ECH61H) for E6000 EmulatorUser’s ManualUser’s ManualRev.1.0 2003.02
Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intel
Comments to this Manuals