Renesas H8/36109 User Manual

Revision Date: Apr. 06, 2006Renesas Microcomputer Development Environment System H8 Family / H8/300H Tiny Series HS36109ECH61HE Rev.1.00 H8

VI Warnings on Emulator Usage Be sure to read and understand the warnings below before using this emulator. Note that these are the main warnings, n

i Preface Thank you for purchasing this user system interface cable (HS36109ECH61H) for the Renesas’ original microcomputer H8/36109 group. The HS36

ii Contents Preface ...i Section 1 Configur

1 Section 1 Configuration CAUTION Use an NQPACK100SD-ND socket (manufactured by Tokyo Eletech Corporation) for the FP-100U package IC so

2 Table 1 lists the HS36109ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS36109ECH61H Components N

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Expansion I/O Board WARNING Observe the precautions listed be

4 2. After making sure the direction of the cable body connector is correct, firmly insert the cable body connector into the expansion I/O board so

5 2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the US

6 2.2.4 Fastening Cable Head CAUTION 1. Use a Philips-type screwdriver whose head matches the screw head. 2. The tightening torque must

7 Fasten the user system interface cable head to the IC socket for an FP-100U package on the user system with the four screws (M2 x 10 mm) provided.

8 2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable bodyCable headRemove jigUser systemPush two remove jigs.Removing Figur

9 2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system

10 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. Uni

11 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable

12

13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided

14 MCUPin 1IC socket (NQPACK100SD-NDmanufactured by Tokyo Eleteck Corporation)User systemScrews (M2 x 6 mm)Socket cover Figure 8 Installing MCU to

15 Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8/3664 E6000 Emulator User’s Manual (HS366

16 Figure 9 shows the system clock oscillator on the user system interface cable and the subclock input specifications. To E6000 emulatorSystem cloc

17 Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the c

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the cu

H8/36109 Group FP-100U User System Interface Cable HS36109ECH61H User's ManualPublication Date: Rev.1.00, April 6

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japanhttp://www.renesas.comRefer to

H8/36109 Group FP-100U User System Interface Cable HS36109ECH61H User’s Manual

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future

II LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifications and free from d

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages

IV SAFETY PAGE READ FIRST • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future referenc

V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emu