Renesas H8S/2338 Series Technical Information

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

IIILIMITED WARRANTYHitachi warrants its emulator products to be manufactured inaccordance with published specifications and free from defects inmateri

IVState Law:Some states do not allow the exclusion or limitation of implied warranties or liability forincidental or consequential damages, so the abo

VSAFETY PAGEREAD FIRST READ this user's manual before using this emulator product. KEEP the user's manual handy for future reference.Do

VIWARNINGObserve the precautions listed below. Failure to do soObserve the precautions listed below. Failure to do soObserve the precautions lis

iPrefaceThank you for purchasing the H8S/2339, H8S/2338, H8S/2329, H8S/2328, H8S/2318, H8S/2319F,H8S/2315F series E6000 emulator.The H8S/2339, H8S/233

iiNote: Microsoft®, Windows® and WindowsNT® are registered trademarks of MicrosoftCorporation in the United States and/or in other countries.

iiiContentsSection 1 Overview ... 11.1 Environment Conditions..

ivFiguresFigure 2.1 Default User System Interface Circuit...7Figure 2.2 Use

1Section 1 OverviewThe H8S/2339, H8S/2338, H8/2329, H8S/2328, H8S/2318, H8S/2319F and H8S/2315F seriesE6000 emulator (hereafter referred to as the E

21.21.21.21.2 Supported MCUs and User System Interface CablesSupported MCUs and User System Interface CablesSupported MCUs and User System Interface C

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

3H8S/2318 Series:H8S/2318 Series:H8S/2318 Series:H8S/2318 Series:Table 1.4 H8S/2318 Series MCUs and User System Interface CablesNo.MCU TypeNumber Pack

41.31.31.31.3 Operating Voltage and Frequency SpecificationsOperating Voltage and Frequency SpecificationsOperating Voltage and Frequency Specificatio

5In the E6000, the clock can be selected by using the Configuration window or the Clockcommand.Table 1.6 Clock SelectionsClock CommandParameterConfigu

6Section 2 User System InterfaceAll user system interface signals are directly connected to the MCU in the E6000 with no bufferingexcept for those l

7Default:Default:Default:Default:Figure 2.1 Default User System Interface CircuitMode Pins (MD2, MD1, and MD0) and NMI: Mode Pins (MD2, MD1, and

8AN0 to AN7, AN12 to AN15, DA0 to DA3, AVcc, AVss, and Vref:AN0 to AN7, AN12 to AN15, DA0 to DA3, AVcc, AVss, and Vref:AN0 to AN7, AN12 to AN15, DA0 t

9Section 3 Notes on Use3.13.13.13.1 I/O Register Differences between Actual MCU and E6000I/O Register Differences between Actual MCU and E6000I/O Re

103. If the reserved area other than that described in item 1 above is used, the operation in the actualMCU cannot be guaranteed. If the user progr

11Section 4 HDI Parameters4.14.14.14.1 Address AreasAddress AreasAddress AreasAddress AreasTable 4.1 lists the parameters for address areas (Area) t

124.24.24.24.2 Access StatusAccess StatusAccess StatusAccess StatusTable 4.2 lists the parameters for access status (Status) that can be specified wit

Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp.The semiconductor operati

13Section 5 Diagnostic Test ProcedureThis section describes the diagnostic test procedure using the E6000 test program.5.15.15.15.1 System Set-Up fo

145.25.25.25.2 Diagnostic Test Procedure Using TesDiagnostic Test Procedure Using TesDiagnostic Test Procedure Using TesDiagnostic Test Procedure Usin

15It will take about 6 minutes to execute the test program when the host computer usingWindows®98 runs at 166 MHz and the PCI interface board is used.

16Downloading firmware ...Loading the test program.01) Testing Main Board Register :IDR0 Register...OKShows the check resultsPAGE

17E6000 (normal completion).Marching Test. page range H'000 - H'04f ...OKShows the results of steptest for the trace RAM (lasthalf) in

18GRD Break ...OKcontrolling circuits in the E6000Setting up, please wait..(normal completion).WPT Break ...

19C)PERM_SUBROUTINE Time Measure Test ...OK(normal completion).D)PERM Time Out Bit TestTime Out Test 1...OKTime Out Tes

H8S/2339, H8S/2338, H8S/2329, H8S/2328, H8S/2318, H8S/2319F, H8S/2315F Series E6000 Emulator HS2339EPI61HSupplementary InformationUser’s ManualRev.1.0

Cautions1. Hitachi neither warrants nor grants licenses of any rights of Hitachis or any third partys patent,copyright, trademark, or other intellec

IIMPORTANT INFORMATIONREAD FIRST READ this user's manual before using this emulator product. KEEP the user's manual handy for future

IIIt is highly recommended that first-time users be instructed by users that are well versed in theoperation of the emulator product.