Renesas M16C/26A Technical Information

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

Chapter 5. Block Diagram Figure 5-1 is representative of the CPU board components and their connectivity. Boot mode pinsBOOTCircuitryD-typeLatchRESE

Chapter 6. User Circuitry 6.1. Switches There are four switches located on the Renesas Starter Kit. The function of each switch and its connection a

6.3. Potentiometer A single turn potentiometer is connected to AN2.4 (P9.3) of the microcontroller. This may be used to vary the input analog voltage

6.6.Option Links Table 6-5 below describes the function of the option links associated with Power configuration. The default configuration is indicat

Table 6-6 below describes the function of the option links associated with Clock configuration. The default configuration is indicated by BOLD text.

Table 6-8 below describes the function of the option links associated with Analog configuration. The default configuration is indicated by BOLD text.

Table 6-10 below describes the function of the option links associated with other options. The default configuration is indicated by BOLD text. Optio

6.7.Oscillator Sources A crystal oscillator or ceramic resonator is fitted on the Renesas Starter Kit and used to supply the main clock input to the

Chapter 7. Modes The Renesas Starter Kit supports Boot mode and Single chip mode. Details of programming the FLASH memory is described in the M16C/2

Chapter 8. Programming Methods The board is intended for use with High-performance Embedded Workshop and the supplied E8a debugger. Refer to M16C/26

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

Chapter 9. Headers 9.1. Microcontroller Headers Table 9-1 to Table 9-4 show the microcontroller pin headers and their corresponding microcontroller

J4 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 IO_7 37 2 IO_6 38 3 IO_5 39 4 TRISTn/IO_4* 40 5 AD3 41 6 AD2 42 7 A

JA2 Pin Header Name Circuit Net Name Device Pin Pin Header Name Circuit Net Name Device Pin 1 Reset RESn 7 2 External Clock Input CON_XIN*

Chapter 10.Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the Renesas Starter Kit board must be connected

10.4. Memory Map Figure 10-1: Memory Map 20

Chapter 11. Component Placement Figure 11-1: Component Placement 21

Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop, refer to the High-performance Embedded Workshop man

Renesas Starter Kit for M16C/26A User's Manual Publication Date Rev.3.00 Aug.31,2007 Published by: Renesas Tech

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanRenesas Starter Kit for M16C/26AREG10J0040-0300User’s Manual

Renesas Starter Kit for M16C/26AUser’s ManualUser’s ManualRev.3.00 2007.08RENESAS 16-BIT SINGLE-CHIP MICROCOMPUTERM16C FAMILY / M16C/Tiny SERIES

Table of Contents Chapter 1. Preface...

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this d

Chapter 2. Purpose This Renesas Starter Kit is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Program

Chapter 3. Power Supply 3.1. Requirements This Renesas Starter Kit operates from a 3V to 5V power supply. A diode provides reverse polarity protecti

Chapter 4. Board Layout 4.1. Component Layout The following diagram shows the top layer component layout of the board. Figure 4-1: Board Layout 4

4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” gri