Renesas SH7085 User Manual

Revision Date: Feb. 26, 2007Renesas Microcomputer Development Environment SystemSuperH™ Family / SH7080 Series R0E570850CFK00 Rev.4.00 SH70

VI means WARNING or CAUTION. Example: CAUTION AGAINST AN ELECTRIC SHOCK means PROHIBITION. Example: DISASSEMBLY PROHIBITED means A FORCIBLE ACTI

VII WARNING Warnings for AC Power Supply: • If the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do no

VIII WARNING • If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unp

IX CAUTION Cautions for AC Adapter: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. D

X WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul

i Preface The R0E570850CFK00 is a user system interface board that connects a user system for the SH7085 PLQP0144KA-A (former code: FP-144LV) package

ii

iii Contents Section 1 Configuration ...1 Section 2 Environment

iv

1 Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the PLQP0144KA-A (forme

2 CAUTION Use a NQPACK144SD-ND socket (manufactured by Tokyo Eletech Corporation) and a HQPACK144SD (manufactured by Tokyo Eletech Corporation) f

3 Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Specificati

4

5 Section 3 User Interface Specifications This user system interface board has the function that masks the chip select signals (CS0 to CS7), bus re

6 Table 3 Setting a Switch (SW1) Switch Setting SW1 No. PLQP0144KA-A (Former Code: FP-144LV) Socket Pin No. Signal Name On Off 1

7 Table 5 Setting a Switch (SW3) Switch Setting SW2 No. PLQP0144KA-A (Former Code: FP-144LV) Socket Pin No. Signal Name On Off 1

8 Figure 3 shows a circuit for masking signals on the user system interface board. UVCCPB7PB8PD28PD29PA18PA17PA 1PA11PE6PA 7PE5PA 0PA10PA20PA 6PA21SW

9 Section 4 Connection Procedures 4.1 Connecting User System Interface Board to User System WARNING Always switch OFF the user system and the

10 4.1.2 Installing Cable Head CAUTION Check the location of pin 1 before inserting. If the IC socket is not connected properly, the power-suppl

11 Fasten the user system interface board to the IC socket for a PLQP0144KA-A (FP-144LV) package on the user system with the four screws (M2.0 x 10 m

1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use

12 4.2 Connecting User System Interface Board to EV-Chip Board WARNING Observe the precautions listed below. Failure to do so will result in

13 BoardSpacerUser systemEV-chip unitConnector No.User I/F Connector 1(CN4)EV-Chip Unit Connector No.Board Connector No.UCN1UCN2User I/F Connector 2(

14 4.3 Recommended Dimensions for User System Mount Pad (Footprint) Figure 6 shows the recommended dimensions for the mount pad (footprint) for the

15 4.4 Dimensions for External Bus Trace Unit, Emulation Memory Unit, EV-Chip Unit, and User System Interface Board The dimensions for the external

16 125.090.090.045.05.0125.090.0110.020.030.060.05.0125.090.0Unit: mmTolerance: ±0.5 mmExternal bus trace unitBoardSpacerEV-chip unitPin 1Emulation m

17 4.5 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board

18 24.539.1939.1924.542.112.555.530.037.527.529.224.5IC socket(NQPACK144SD-ND manufactured by Tokyo Eletech Corporation)User systemSpacer (φ6.0)Unit:

19 24.529.212.542.630.037.527.5EV-chip unitSpacer (φ6.0)IC socket(NQPACK144SD-ND manufactured by Tokyo Eletech Corporation)User systemUnit: mmToleran

20

21 Section 5 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver

22 MCU (SH7085)Screws (M2.0 x 6 mm)Socket coverPin 1User systemIC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) Figure 11 Insta

23 Section 6 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH-2A, SH-2 E200F Emulator User's Manua

24

25 Section 7 Notice 1. Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. 2. Do not apply exces

26

SH7085 Group PLQP0144KA-A User System Interface BoardUser's Manual Publication Date: Rev. 1.00, December 14, 2004

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japanhttp://www.renesas.comRefer to

SH7085 Group PLQP0144KA-A User System Interface Board User’s Manual

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future

II Target User of the Emulator Product: This emulator product should only be used by those who have carefully read and thoroughly understood th

III LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifications and free from d

IV State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,

V SAFETY PAGE READ FIRST • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future reference.