Renesas Single-Chip Microcomputer H8/36079 User Manual

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

Chapter 5. Block Diagram Figure 5-1 shows the CPU board components and their connectivity. Figure 5-1: Block Diagram Figure 5-2 shows the connection

Chapter 6. User Circuitry 6.1. Switches There are four switches located on the CPU board. The function of each switch and its connection are shown i

Description Function Circuit Net Name Device Pin SCI3 Programming serial port TxD 46 SCI3 Programming serial port RxD 45 SCI3_2 Spare Seria

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R2 E8A Fitted if one of the following condition is satisfied: 1.

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R16 Serial Port Configuration Connects serial port SCI3_2 (Rx) to

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R38 CPU reset signal Enables CPU reset signal Disables CPU reset

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R56 Processor Oscillator Source External Clock Source Internal Cl

oscillators that are fitted and alternative footprints provided on this RSK: Component Crystal (X1) Fitted 32.768 KHz (90SMX package) Crystal (X2)

Chapter 7. Modes This RSK supports Boot mode and User mode. Details of programming the FLASH memory is described in the H8/38347 Group Hardware Manu

Chapter 8. Programming Methods The board is intended for use with HEW and the supplied E8A debugger. Refer to H8/36079 Group Hardware Manual for det

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

Chapter 9. Headers 9.1. Microcontroller Headers Table 9-1 to show theTable 9-4 microcontroller pin headers and their corresponding microcontrolle

J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 TMR1 33 2 Up 34 3 NMIn 35 4 UD 36 5 Vp 37 6 Wp 38 7 Vn 39 8 Wn

9.2. Application Headers Table 9-5 and belowTable 9-6 show the standard application header connections.JA1 Pin Generic Header Name CPU board Sig

Chapter 10.Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the RSK board must be connected to a PC USB por

Chapter 11.Component Placement Figure 11-1: Component Placement 20

Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop (HEW, refer to the HEW manual available on the CD or

Renesas Starter Kit for H8/36079 User's Manual Publication Date Rev.1.00 17.10.2007 Published by: Renesas Tech

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanRenesas Starter Kit for H8/36079REG10J0076-0100User’s Manual

Renesas Starter Kit for H8/36079User’s ManualUser’s ManualRev.1.00 2007.10RENESAS SINGLE-CHIP MICROCOMPUTERH8 FAMILY/ H8/300H Tiny Series

Table of Contents Chapter 1. Preface...

1Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this

2Chapter 2.Purpose This RSK is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Programming. • User C

Chapter 3.Power Supply 3.1. Requirements This RSK operates from a 5V power supply. A diode provides reverse polarity protection only if a current lim

Chapter 4. Board Layout 4.1. Component Layout The following diagram shows top layer component layout of the board. User switches E8A Header Power

4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” grid