To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C
i Preface Thank you for purchasing this user system interface cable (HS2655ECH61H) for the Renesas’s original microcomputer H8S/2655 group. The HS265
ii Contents Section 1 Configuration...1 Section 2 Connection Pr
1 Section 1 Configuration CAUTION Use an NQPACK128RD socket (manufactured by Tokyo Eletech Corporation) for the FP-128 package IC socket
2 Figure 1 HS2655ECH61H User System Interface Cable
3 Table 1 lists the HS2655ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2655ECH61H Components No.
4 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below.
5 Figure 2 Connecting User System Interface Cable to Emulator Station
6 2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USE
7 User systemBottom view of IC socket4 projections to apply epoxyadhesice toIC socket(Tokyo Eletech CorporationNQPACK128RD)Guide pinsPin 1 Figure 3
8 2.2.4 Fastening Cable Head CAUTION 1. Use the screwdriber provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less
Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang
9 Figure 4 Connecting User System Interface Cable to User System
10 2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable bodyCable headRemove jigPush the remove jigRemovingUser system Figure
11 2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system
12 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Figure 7
13 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable
14 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided f
15 User systemScrews (M2 x 6 mm)IC socketTokyo Eletech CorporationNQPACK128RDSocket coverMCUPin 1 Figure 9 Installing MCU to User System
16 Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2655 group, turn on the emulator according to the procedures describ
17 Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the ca
18 6. The JP1 jumper socket is used for testing. Do not remove the inserted jumper pin. JP1 Figure 12 JP1 Jumper Socket
H8S/2655 Group QFP-128User System Interface CableHS2655ECH61H User’s ManualUser’s Manual Rev.4.0 2004.01Renesas Microcomputer Development Environmen
H8S/2655 Group QFP-128User System Interface Cable HS2655ECH61H User's ManualPublication Date: Rev.4.00, Janu
1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanH8S/2655 Group QFP-128User System Interface CableREJ10B0086-0400HHS2655ECH61H Us
Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better an
I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy
II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and f
III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,
IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for futur
V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul
Comments to this Manuals