Renesas SuperH HS7630KCM02HE User Manual

2003.7.3 SuperH Family E10A Emulator Additional Document for User’s Manual SH7630 E10A HS7630KCM02HE Renesas Microcomputer Development E

6 Notes: H-UDI port connector(Pin 1 mark)(top view)Unit: mm4.8M2.6 x 0.459.00.33.9 H-UDI port connector (front view)1. Input to or output from the u

7 Pin 1 markNotes: 1. Input to or output from the user system.2. The slash (/) means that the signal is active-low.3. The emulator monitors the GND

8 1.5 Recommended Circuit between the H-UDI Port Connector and the MPU 1.5.1 Recommended Circuit (36-Pin Type) Figure 1.4 shows a recommended circ

9 1AUDATA0AUDATA2AUDATA1AUDATA3TCKTMSAUDSYNCN.C.N.C.RESETTDITDOTRSTASEBRKAKNCGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGNDGND35791113151719

10 1.5.2 Recommended Circuit (14-Pin Type) Figure 1.5 shows a recommended circuit between the H-UDI port connector and the MPU. Notes: 1. Do no

11 1TCKTMSRESETTDITDOTRSTASEBRKAKGNDGNDGNDGNDGNDGND234567ASEMD0891110121314TCKRESETPTMSTDOTDITRSTASEBRKAKNCSH7630VccQ (3.3 V)VccQ (3.3 V)H-UDI port

12

13 Section 2 Specifications of the SH7630 E10A Emulator’s Software 2.1 Differences between the SH7630 and the Emulator • When the emulator syste

14 • Reset Signals The SH7630 reset signals are only valid during emulation started with clicking the GO or STEP-type button. If these signals are

15 • UBC When [User] is specified in the [UBC mode] list box in the [Configuration] dialog box, the UBC can be used in the user program. Do not use

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products bett

16 • Illegal Instructions If illegal instructions are executed by STEP-type commands, the emulator cannot go to the next program counter. 2.2 Spec

17 Table 2.4 Types of Break Conditions Break Condition Type Description Address bus condition (Address) Breaks when the SH7630 address bus value

18 Table 2.5 lists the combinations of conditions that can be set under Break Condition 1, 2, 3. Table 2.5 Dialog Boxes for Setting Break Conditio

19 AUD Trace Functions: This function is operational when the AUD pin of the device is connected to the emulator. Table 2.8 shows the AUD trace ac

20 To set the AUD trace acquisition mode, click the [Trace] window with the right mouse button and select [Setting] from the pop-up menu to display

21 (a) Branch Trace Function The branch source and destination addresses and their source lines are displayed. Branch trace can be acquired by selec

22 Figure 2.3 [Window trace] Page Note: When the [L-bus] or [I-bus] radio button is selected, the following bus cycles will be traced. L-bus: A

23 (c) Software Trace Function Note: This function can be supported with SHC compiler V7.0 and later. When a specific instruction is executed, the

24 Internal Trace Function: This function is activated by selecting the [Internal trace] radio button in the [Trace type] group box of the [Trace m

25 6. When a BREAKPOINT is set to the slot instruction of a delayed branch instruction, the PC value becomes an illegal value. Accordingly, do not

i Contents Section 1 Connecting the Emulator with the User System...1 1.1 Components of the Emulator ...

26 2.2.7 Notes on Setting the UBC_MODE Command In the [Configuration] window, if [User] is set while the [UBC mode] list box has been set, the STEP

27 Figure 2.4 [Performance Analysis] Dialog Box  Measurement range One of the following ranges can be specified. This depends on the item selec

28 2. Step execution is not possible when Break condition 1->2 or Break condition 2->1 is selected for the PERFORMANCE_SET command or in [Mod

29 Table 2.10 Measurement Item Selected Name Option Disabled None Elapsed time AC Number of execution states VS Branch instruction counts B

30 Table 2.10 Measurement Item (cont) Selected Name Option Cacheable area instruction access cycle CIC Cacheable area data access cycle CDC Ac

SuperHTM Family E10A Emulator Additional Document for User's ManualSpecific Guide for the SH7630 E10A Emulato

SuperH Family E10A Emulator Additional Document for User’s Manual REJ10B0015-0100H

ii

1 Section 1 Connecting the Emulator with the User System 1.1 Components of the Emulator The SH7630 E10A emulator supports the SH7630. Table 1.1

2 Table 1.1 Components of the Emulator (HS7630KCM01H, HS7630KCM02H, HS7630KCI01H, or HS7630KCI02H) Classi-fication Component Appearance Quan-tit

3 For EMI countermeasure, use the ferrite core by connecting the user interface cable. When the user interface cable is connected with the emulato

4 1.2 Connecting the E10A Emulator with the User System To connect the E10A emulator (hereinafter referred to as the emulator), the H-UDI port conn

5 1.3 Installing the H-UDI Port Connector on the User System Table 1.3 shows the recommended H-UDI port connectors for the emulator. Table 1.3 R