Renesas User System Interface Cable HS2633ECH61H User Manual

2004.1.29 H8S/2633 Group QFP-128 User System Interface Cable HS2633ECH61H User’s Manual Renesas Microcomputer Development Environment System Rev.5

1 Section 1 Configuration CAUTION Use an NQPACK128RD socket (manufactured by Tokyo Eletech Corporation) for the FP-128 package IC socket

2 Figure 1 HS2633ECH61H User System Interface Cable

3 Table 1 lists the HS2633ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2633ECH61H Components No.

4 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below.

5 Figure 2 Connecting User System Interface Cable to Emulator Station

6 2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USE

7 Figure 3 Location Setting of IC Socket 2.2.2 Soldering IC Socket After fastening, solder the IC socket for an FP-128 package to the user syste

8 2.2.4 Fastening Cable Head CAUTION 1. Use the screwdriber provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less

9 Figure 4 Connecting User System Interface Cable to User System

10 2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable bodyCable headRemove jigPush the remove jigRemovingUser system Figure

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better an

11 2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system

12 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Figure 7

13 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable

14 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided f

15 User systemScrews (M2 x 6 mm)IC socketTokyo Eletech CorporationNQPACK128RDSocket coverMCUPin 1 Figure 9 Installing MCU to User System

16 Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2633 group, turn on the emulator according to the procedures describ

17 Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the ca

H8S/2633 Group QFP-128User System Interface Cable HS2633ECH61H User's ManualPublication Date: Rev.5.00, Janu

H8S/2633 Group QFP-128 User System Interface Cable HS2633ECH61H User’s Manual REJ10B0085-0500H

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy

II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and f

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for futur

V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul

i Preface Thank you for purchasing this user system interface cable (HS2633ECH61H) for the Renesas’ original microcomputer H8S/2633 group. The HS2633

ii Contents Section 1 Configuration.....................1 Section 2 Connection Pr