Renesas forM16C/20 User Manual

M30200T-RPD-EEmulation Pod forM16C/20 SeriesUser's ManualRev.1.00September 1, 2003REJ10J0264-0100Z

( 10 / 32 )WARNINGWarning for Installation:• Do not set this product in water or areas of high humidity. Make sure that the emulation pod mainunit doe

( 11 / 32 )Notes on the Target System:•Because the emulation pod main unit does not have the capacity to supply power to other devices,design your sys

( 12 / 32 )IMPORTANTNotes on Connecting Pod Probe and Pitch Converter Board:• Prepare the right pod probe for your MCU. Without a pod probe this produ

( 13 / 32 )Notes on MAP References and Settings:• When starting up M30200T-RPD-E, initial MAP settings are as follows.0000016 to 003FF16: EXT0040016 t

( 14 / 32 )Note on BRK Instruction:• BRK instruction cannot be used.Note on Software Break and Hardware Break:•A software break and a hardware break c

( 15 / 32 )Chapter 2. IntroductionM30200T-RPD-E is used by connecting to the PC4701 emulator main unit. Figure 2.1 shows thesystem configuration.Figur

( 16 / 32 )Chapter 3. SpecificationsTable 3.1 lists the specifications of M30200T-RPD-E.Table 3.1 Specifications of M30200T-RPD-EUsable emulator main

( 17 / 32 )Chapter 4. Setting Up4.1 Removing the Upper CoverIf you need to change the input frequency, remove the upper cover of the product to change

( 18 / 32 )4.2 Setting Oscillation FrequencyWhen you are using the emulation pod main unit's internal oscillator, see (1) below, and when youare

( 19 / 32 )Figure 4.3 Circuit of oscillator board OSC-2Figure 4.3 shows the OSC-2 circuit. Use the circuit constants recommended by themanufacturer of

( 2 / 32 )Keep safety first in your circuit designs!• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into mak

( 20 / 32 )Figure 4.4 Replacing small oscillator circuit boardsHow to replace the oscillator circuit board is shown in Figure 4.4 below.(1) Unscrew th

( 21 / 32 )Figure 4.5 External oscillator circuitFigure 4.6 Circuit in which oscillation does not occur(2) Using target system's oscillatora. To

( 22 / 32 )Chapter 5. Connection5.1 Connection to the Emulator Main UnitUse the FLX120-RPD 120-pin flexible cable (included with the package) to conne

( 23 / 32 )5.2 Connection to the Emulation PodAttach the FLX120-RPD to M30200T-RPD-E, then secure them with the screws. Figure 5.2 showshow to connect

( 24 / 32 )5.3 Connection to the Pod ProbeThe emulation pod for M16C/20 Series consists of the M30200T-RPD-E emulation pod main unitand the M302xxT-PR

( 25 / 32 )Chapter 6. External DimensionsFigures 6.1 shows external dimensions of M30200T-RPD-E.Figure 6.1 External dimensions of M30200T-RPD-EUnit: m

( 26 / 32 )Figure 6.2 External dimensions of FLX64-PRBUnit: mmFigures 6.2 shows external dimensions of the FLX64-PRB pitch converter board for connect

( 27 / 32 )Chapter 7. Maintenance and Guarantee7.1 MaintenanceIf dust or dirt collects on any equipment of your emulation system, wipe it off with a d

( 28 / 32 )7.4 How to Request for RepairIf your product is found faulty, follow the procedure below to send your product for repair.Customer Fill in t

( 29 / 32 )Chapter 8. TroubleshootingWhen the M30200T-RPD-E does not work properly, check the items listed below.(1) The emulator main unit cannot be

( 3 / 32 )PrefaceThe M30200T-RPD-E is an emulation pod main unit for M16C/20 Series of Renesas 16-bitmicrocomputers. The M30200T-RPD-E is used by conn

( 30 / 32 )MEMO

M30200T-RPD-E User's ManualRev.1.00September 1, 2003REJ10J0264-0100ZCOPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATIONAND RENESAS SOLUTIONS CORPORATI

( 4 / 32 )ContentsSummary...

( 5 / 32 )Chapter 6. External Dimensions ...25Chapter 7. Maint

( 6 / 32 )SummaryChapter 1. Precautions for SafetyThis chapter describes the precautions which should be taken in order to use M30200T-RPD-E safelyand

( 7 / 32 )TerminologySome specific words used in this User's Manual are defined as follows:Emulator systemThis means an emulator system built aro

( 8 / 32 )Things to Check When UnpackingThe M30200T-RPD-E consists of the following parts and manuals. When unpacking, check to seeif your M30200T-RPD

( 9 / 32 )Chapter 1. Precautions for SafetyIn both the user's manual and on the product itself, several icons are used to insure proper handlingo