Renesas M37900T2-RPD-E User Manual

M37900T2-RPD-EEmulation Pod for 7900 Series MCUsUser's ManualRev. 1.00July 1, 2003REJ10J0191-0100Z

( 10 / 52 )Notes on Power Supply to the Target System:• The Vcc pin of the emulator is connected to the target system to observe the voltage of the ta

( 11 / 52 )IMPORTANTNotes on EMEM Dialog:• When setting the EMEM dialog box of the emulator debugger M3T-PD79, pay attention to thefollowing:(1) Proce

( 12 / 52 )MEMO

( 13 / 52 )Chapter 2. PreparationThis chapter describes the package components, the system configuration and the preparation for using this product fo

( 14 / 52 )Chapter 2. Preparation2.1 TerminologySome specific words used in this user's manual are defined as follows:PC4701 systemThis means an

( 15 / 52 )2.2 Package ComponentsThe M37900T2-RPD-E package consists of the following items. When unpacking, check to see ifyour M37900T2-RPD-E contai

( 16 / 52 )2.4 Name of Each Part(1) System ConfigurationFigure 2.1 System configuration(1) Emulation pod (M37900T2-RPD-E)This is an emulation pod for

( 17 / 52 )(2) Inside of the Emulation PodFigure 2.2 Internal view of the emulation pod(1) Base boardBase board which controls the interface with the

( 18 / 52 )2.5 When Using the Emulator for the First TimeIf you have purchased this emulation pod newly, it is necessary to download the firmware. The

( 19 / 52 )Chapter 3. Setting UpThis chapter describes switch settings required for using this product and how to connect this product to the PC4701 a

( 2 / 52 )Keep safety first in your circuit designs!• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into mak

( 20 / 52 )Chapter 3. Setting UpTo use this emulation pod with your application system, it is necessary to set as follows. Set thefollowing after remo

( 21 / 52 )(1) Using the Oscillator Circuit on the Target SystemWhen turning on the power supply, the internal clock of the emulation pod is selected

( 22 / 52 )(2) Changing the Internal Oscillator Circuit of the Emulation PodAn oscillator circuit board for 20 MHz is mounted on this product and an o

( 23 / 52 )(3) Replacing the Oscillator Circuit BoardsFigures 3.5 and 3.6 show how to replace the oscillator circuit board. For the location of the os

( 24 / 52 )3.2 Connecting the Pod Probe and Emulation PodThe 7900 Series emulation pod consists of the following 2 products. How to connect them is sh

( 25 / 52 )With the 7900 Series emulator system, the internal flash ROM of the emulator MCU is used as anemulation memory.As write/erase iterations to

( 26 / 52 )3.3 Connecting the PC4701 and Emulation PodTo connect the emulation pod to the PC4701, use the FLX120-RPD 120-pin flexible cable includedwi

( 27 / 52 )(2) Connecting the Cable to the Emulation PodFigure 3.10 shows how to connect the FLX120-RPD and the emulation pod.Figure 3.10 Connecting F

( 28 / 52 )MEMO

( 29 / 52 )Chapter 4. UsageThis chapter describes from turning on the power of this product to starting up the emulator debugger.4.1 Turning on Power

( 3 / 52 )PrefaceThe M37900T2-RPD-E is an emulation pod for the 7900 Series of 16-bit microcomputers. It's usedwith a PC4701 emulator.The M37900T

( 30 / 52 )Chapter 4. Usage4.1 Turning on Power(1) Checking the Connection of the SystemBefore turning the power ON, check the connection of the PC470

( 31 / 52 )(3) LED Display When PC4701 Starts up NormallyAfter the emulator starts up, check the status of the LEDs on the front panel to see whether

( 32 / 52 )4.2 Downloading Firmware(1) When It is Necessary to Download FirmwareIt is necessary to download firmware when:(1) you use this product for

( 33 / 52 )4.3 Starting Up the Emulator Debugger (Setting EMEM Dialog)The EMEM dialog box appears when you have started the emulator debugger and set

( 34 / 52 )Figure 4.3 Self-check procedure4.4 Self-check(1) Self-check ProcedureTo run the emulator self-check, do so as explained here below. While t

( 35 / 52 )IMPORTANTNote on Self-check:• If the self-check does not result normally (excluding target status errors), theemulation pod may be damaged.

( 36 / 52 )MEMO

( 37 / 52 )Chapter 5. SpecificationsThis chapter describes specifications of this product.5.1 Specifications ...

( 38 / 52 )Chapter 5. Specifications5.1 SpecificationsTable 5.1 lists the specifications of the M37900T2-RPD-E.Table 5.1 Specifications of the M37900T

( 39 / 52 )Figure 5.1 External dimensions of the emulation pod5.2 External Dimensions of the Emulation PodUnit: mm

( 4 / 52 )ContentsChapter 1. Precautions for Safety ...71.1 Sa

( 40 / 52 )MEMO

( 41 / 52 )Chapter 6. TroubleshootingThis chapter describes how to troubleshoot when this product does not work properly.6.1 Flowchart to Remedy the T

( 42 / 52 )Chapter 6. Troubleshooting6.1 Flowchart to Remedy the TroublesFigure 6.1 shows the flowchart to remedy the troubles from when power to the

( 43 / 52 )6.2 When the Emulator Debugger Does Not Start Up Properly(1) When the LED Display of the PC4701 is AbnormalTable 6.1 LED's abnormal di

( 44 / 52 )(2) Errors Occur at Debugger Startup (target connected)Table 6.2 Checkpoints of errors of the emulator debugger M3T-PD79 (target is connect

( 45 / 52 )(3) Errors Occur at Debugger Startup (target not connected)Table 6.3 Checkpoints of errors of the emulator debugger M3T-PD79 (target is not

( 46 / 52 )6.3 Operation Differs from that of MCUs with Flash Memory(1) Initializing the Internal Resources of an MCU at Power-onWith this product, th

( 47 / 52 )Chapter 7. Maintenance and GuaranteeThis chapter describes how to maintenance, repair provisions and how to request for repair.7.1 Maintena

( 48 / 52 )Chapter 7. Maintenance and Guarantee7.1 MaintenanceIf dust or dirt collects on any equipment of your emulation system, wipe it off with a d

( 49 / 52 )7.4 How to Request for RepairIf your product is found faulty, follow the procedure below to send your product for repair.Customer Fill in t

( 5 / 52 )Chapter 5. Specifications ...375.1 Specif

( 50 / 52 )MEMO

M37900T2-RPD-E User's ManualRev. 1.00July 1, 2003REJ10J0191-0100ZCOPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATIONAND RENESAS SOLUTIONS CORPORATION

( 6 / 52 )MEMO

( 7 / 52 )Chapter 1. Precautions for SafetyThis chapter describes precautions for using this product safely and properly. For precautions for the pod

( 8 / 52 )Chapter 1. Precautions for SafetyIn both the user's manual and on the product itself, several icons are used to insure proper handlingo

( 9 / 52 )WARNINGWarning for Installation:• Do not set this product in water or areas of high humidity. Spilling water or some other liquid intothe ma