To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C
IV State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,
V SAFETY PAGE READ FIRST • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future reference.
VI means WARNING or CAUTION. Example: CAUTION AGAINST AN ELECTRIC SHOCK means PROHIBITION. Example: DISASSEMBLY PROHIBITED means A FORCIBLE ACTI
VII WARNING Warnings for AC Power Supply: • If the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do no
VIII WARNING • If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unp
IX CAUTION Cautions for AC Adapter: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. D
X WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul
i Preface The R0E572110CFK00 is a user system interface board that connects a user system for the SH7211 FP-144L package to the SH7211 E200F emulator
ii Contents Section 1 Configuration... 1 Section 2 Environmenta
1 Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the FP-144L package. P
Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang
2 CAUTION Use a NQPACK144SD socket (manufactured by Tokyo Eletech Corporation) for the FP-144L package IC socket on the user system. Table 1 R0E
3 Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Specificati
4 Section 3 Connection Procedures 3.1 Connecting User System Interface Board to User System WARNING Always switch OFF the user system and the
5 3.1.2 Installing Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-144L package on the u
6 BoardScrews (M2.0 x 10 mm)User systemIC socket(NQPACK144SD manufactured by Tokyo Eletech Corporation)Pin 1 Figure 2 Connecting User System Interf
7 3.2 Connecting User System Interface Board to EV-Chip Unit WARNING Observe the precautions listed below. Failure to do so will result in a
8 BoardSpacerUser systemEV-chip unitConnector No.User I/F Connector 1(CN3)EV-Chip Unit Connector No.Board Connector No.UCN1UCN2User I/F Connector 2(C
9 3.3 Recommended Dimensions for User System Mount Pad (Footprint) Figure 4 shows the recommended dimensions for the mount pad (footprint) for the u
10 Pin 17.0φ1.07.00.252.000.50 × 35 = 17.500.50 × 35 = 17.5 19.00 max23.00 min0.50.50Location determination holeUnit: mmDimension and toleranceToler
11 3.4 Dimensions for External Bus Trace Unit, EV-Chip Unit, and User System Interface Board The dimensions for the external bus trace unit, EV-chip
SH7211 Group FP-144LUser System Interface BoardUser’s ManualUser’s Manual Rev.1.01 2006.08Renesas Microcomputer Development Environment SystemSuperH
12 3.5 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board
13 24.542.112.555.530.037.527.529.2IC socket(NQPACK144SD manufactured by Tokyo Eletech Corporation)User systemSpacer (φ6.0)39.1924.524.539.19EV-chip
14 24.529.212.542.630.037.527.5EV-chip unitSpacer (φ6.0)IC socket(NQPACK144SD manufactured by Tokyo Eletech Corporation)User system39.1924.524.539.19
15 Section 4 Installing the MPU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver
16 MPU (SH7211)Screws (M2.0 x 6 mm)Socket coverPin 1User systemIC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) Figure 9 Installin
17 Section 5 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH7211 E200F Emulator User's Manual (R0
18 Section 6 Notice 1. Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. 2. Do not apply exces
SH7211 Group FP-144L User System Interface BoardUser's Manual Publication Date: Rev.1.01, August 8, 2006Publishe
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japanhttp://www.renesas.comRefer to
1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanSH7211 Group FP-144LUser System Interface BoardREJ10J1317-0101User’s Manual
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the cu
I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future
II Target User of the Emulator Product: This emulator product should only be used by those who have carefully read and thoroughly understood th
III LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifications and free from d
Comments to this Manuals