Renesas H8S/2168 User Manual

2003.12.25H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator HS2168ECN61H User’s Manual Renesas Microcomputer Development

7 2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USE

8 Use the guide pins provided to determine where to install the IC socket, as shown in figure 4. User systemIC socket(NQPACK144SE manufactured by To

9 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a TFP-144 package on the use

10 Fasten the user system interface cable head to the IC socket for a TFP-144 package on the user system with the four screws (M2.0 × 10 mm) provided

11 2.2.5 Fastening Cable Body Connect the cable body and EIO board 1 to the cable head. Cable headRemove jigEIO board 1EIO board 1User systemPush th

12 2.3 Recommended Dimensions for User System Mount Pad Figure 7 shows the recommended dimensions for the mount pad (footprint) for the user system

13 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 8. Unit:

14 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable

15 Section 3 Installing the MCU on the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a screwdriver whose head m

16 MCUPin 1IC socket (NQPACK144SEmanufactured by Tokyo Eletech Corporation)User systemScrews (M2.0 x 6 mm)Socket cover Figure 10 Installing MCU to

i Preface Thank you for purchasing this user system interface cable (HS2168ECN61H) for the Renesas’ original microcomputer H8S/2168 group. The HS2168

17 Section 4 User System Interface Circuit The microcomputer (H8S/2168) is installed in this user system interface cable for emulating the LPC func

18 Table 2 Settings of Switches Switch Number Pin 1 Side Pin 3 Side SW1 Port E7 SERIRQ SW2 Port E6 LCLK SW3 Port E5 LRESET_N SW4 Por

19 Section 5 Verifying Operation 1. When using the E6000 emulator for the H8S/2168 group, turn on the emulator according to the procedures describ

20 Section 6 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the ca

21 6. To prevent EMI noise, enclose the user system interface cable head in a case. The recommended material of the case is iron plated with nickel

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products bet

H8S/2168 Group TFP-144User System Interface Cablefor E6000 Emulator User's ManualPublication Date: Rev.1.00,

H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator User’s Manual REJ11Jxxxx-xxxxx

ii Contents Section 1 Configuration...1 Section 2 Connection Pr

1 Section 1 Configuration CAUTION Use an NQPACK144SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-144 package IC socket

2 Table 1 lists the HS2168ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS2168ECN61H Components No.

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below.

4 2.1.1 Connecting User System Interface Cable to Cable Body Connector After making sure the direction of the cable body connector is correct, firml

5 2.1.2 Connecting EIO Board 2 to Emulator 1. Remove four screws at the side of the emulator station. 2. Pull up and remove the cover of the emula

6 2.1.3 Removing EIO Board 2 from Emulator 1. Remove four screws from the side of the emulator station. 2. Pull up and remove the cover of the emu