Renesas FP-144 User Manual

Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp.The semiconductor operati

iPrefaceThank you for purchasing this user system interface cable (HS7043ECH61H) for the Hitachi’soriginal microcomputer SH7040 series.The HS7043ECH61

iiContentsSection 1 Configuration...1Section 2 Connection Procedures .

1Section 1 ConfigurationCAUTIONUse an NQPACK144SD socket (manufactured by TokyoEletech Corporation) for the FP-144 package IC socketon the user system

2Table 1 lists the HS7043ECH61H components. Please make sure you have all of thesecomponents when unpacking.Table 1 HS7043ECH61H ComponentsNo. Compon

3Section 2 Connection Procedures2.1 Connecting User System Interface Cable to Emulator StationWARNINGObserve the precautions listed below. Failure to

42. After making sure the direction of the cable body connector is correct, firmly insert the cablebody connector into the emulator station socket (fi

52.2 Connecting User System Interface Cable to User SystemWARNINGAlways switch OFF the user system and the emulatorproduct before the USER SYSTEM INTE

6Figure 3 Location Setting of IC Socket2.2.2 Soldering IC SocketAfter fastening, solder the IC socket for an FP-144 package to the user system. Be su

72.2.4 Fastening Cable HeadCAUTION1. Use the screwdriver provided for tightening screws.2. The tightening torque must be 0.054 N•m or less.If the appl

8Fasten the user system interface cable head to the IC socket for an FP-144 package on the usersystem with the four screws (M2 x 10 mm) provided. Eac

CautionsKeep safety first in your circuit designs!1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better

92.2.5 Fastening Cable BodyConnect the cable body to the cable head.Figure 5 Fastening Cable Body

102.3 Recommended Dimensions for User System Mount PadFigure 6 shows the recommended dimensions for the mount pad (footprint) for the user systemwith

112.4 Dimensions for User System Interface Cable HeadThe dimensions for the user system interface cable head are shown in figure 7.Figure 7 Dimensions

122.5 Resulting Dimensions after Connecting User System Interface CableThe resulting dimensions, after connecting the user system interface cable head

13Section 3 Installing the MCU to the User SystemCAUTION1. Check the location of pin 1 before inserting.2. Use the screwdriver provided for tighteni

14Figure 9 Installing MCU to User System

15Section 4 Verifying Operation1. When using the E6000 emulator for the SH series, turn on the emulator according to theprocedures described in the

16Section 5 Notice1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cablehead before inserting the cable h

HS7043ECH61HE(A)SH7043 SeriesFP-144User System Interface Cable(HS7043ECH61H)for E6000 EmulatorUser’s ManualADE-702-336Rev. 1.007/08/02Hitachi, Ltd.

Cautions1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’spatent, copyright, trademark, or other intellec

IIMPORTANT INFORMATIONREAD FIRST• READ this user's manual before using this user system interface cable.• KEEP the user's manual handy for f

IILIMITED WARRANTY Hitachi warrants its user system interface cables to be manufacturedin accordance with published specifications and free from d

IIIState Law:Some states do not allow the exclusion or limitation of implied warranties or liability forincidental or consequential damages, so the ab

IVSAFETY PAGEREAD FIRST• READ this user's manual before using this user system interface cable.• KEEP the user's manual handy for future ref

VWARNINGObserve the precautions listed below. Failure to do sowill result in a FIRE HAZARD and will damage the usersystem and the emulator product or