I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy
Section 1 Configuration CAUTION Use an NQPACK144SD socket (manufactured by Tokyo Eletech Corporation) for the FP-144J package IC socket on
2 Table 1 lists the HS2556ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2556ECH61H Components No.
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below. Fa
Figure 2 Connecting User System Interface Cable to Emulator Station 4
2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER S
IC socket(NQPACK144SD manufacturedby Tokyo Eletech Corporation)User systemGuide pins4 projections to applyepoxy resin adhesive to Bottom view of IC so
7 2.2.3 Fastening Cable Head CAUTION 1. Use a Philips-type screwdriver whose head matches the screw head. 2. The tightening torque must b
Fasten the user system interface cable head to the IC socket for an FP-144J package on the user system with the four screws (M2 x 10 mm) provided. Ea
2.2.4 Fastening Cable Body Connect the cable body to the cable head. Cable bodyCable headRemove jigRemovingUser systemPush two remove jigs. Figure 5
2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with
II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Figure 7 Dimen
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head
13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver
MCUPin 1IC socket(NQPACK144SDmanufactured byTokyo Eletech Corporation)User systemScrews (M2 x 6 mm)Socket cover Figure 9 Installing MCU to User Syste
Section 4 Verifying Operation 1. When using the H8S/2556, H8S/2552, and H8S/2506 groups E6000 emulator, turn on the emulator according to the proce
Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable
H8S/2556,H8S/2552H8S/2506 Group FP-144JUser System Interface Cable (HS2556ECH61H)for E6000 Emulator User's M
H8S/2556,H8S/2552,H8S/2506 Group FP-144JUser System Interface Cable (HS2556ECH61H)for E6000 Emulator User’s Manual
III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so
SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future re
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulato
H8S/2556,H8S/2552,H8S/2506 Groups FP-144J User System Interface Cable (HS2556ECH61H) for E6000 Emulator User’s Manual H8S/2556 E6000 HS2556ECH61H
Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products bet
i Preface Thank you for purchasing this user system interface cable (HS2556ECH61H) for the Renesas’s original microcomputer H8S/2556, H8S/2552, and H
ii Contents Section 1 Configuration.....................1 Section 2 Connection P
Comments to this Manuals