Renesas H8/36912 Technical Information

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for futur

V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul

i Preface Thank you for purchasing this user system interface cable (HS36902ECS61H) for the Renesas’ original microcomputer H8/36912, H8/36902 group.

ii Contents Section 1 Configuration...1 Section 2 Connection Pr

1 Section 1 Configuration CAUTION Use an IC83-3204-GS4 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the DP-32S package IC

2 Table 1 lists the HS36902ECS61H components. Please make sure you have all of these components when unpacking. Table 1 HS36902ECS61H Components No

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below.

4 Emulator stationCable body connectorUser system interface cableE6000CTS screws (M3 x 6 mm) Figure 2 Connecting User System Interface Cable to Emu

5 2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USE

6 Cable headPin 1IC socket (IC83-3204-GS4 manufactured by YAMAICHI ELECTRONICS Co., Ltd.)User system Figure 3 Connecting User System Interface Cabl

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

7 2.2.3 Fastening Cable Body Connect the cable body to the cable head. Cable headRemove jigPush the two remove jigs.User systemCable bodyRemoving Fi

8 2.3 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 5. 29.218.431.75

9 2.4 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable h

10 Section 3 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8/3664 E6000 Emulator User’s Manual (HS3664

11 Figure 7 shows the system clock oscillator on the user system interface cable and the subclock input specifications. R2 270 ΩR1 1 MΩHCU04HCU04To E

12 Section 4 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the ca

13 7. SW1 and SW2 are used to switch OSC2 or PC1 and OSC1 or PC0. Turn SW1 and SW2 to the OSC1 and OSC2 sides, respectively, when they are used as O

H8/36912, H8/36902 Group DP-32S User System Interface Cablefor E6000 Emulator User's Manual Publication Date:

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanH8/36912, H8/36902 Group DP-32S User System Interface Cable for E6000 EmulatorRE

H8/36912, H8/36902 Group DP-32SUser System Interface Cablefor E6000 Emulator HS36902ECS61HE User’s ManualUser’s ManualRev.1.00 2004.06HS36902ECS61HR

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the cu

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy

II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and f

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,