Renesas HS1653ECN61H Technical Information

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for futur

V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul

i Preface The HS1653ECN61H is a user system interface board that connects a user system for the H8SX/1653 TFP-120 package to the H8SX/1650 E6000H emu

ii Contents Section 1 Configuration...1 Section 2 Connection Pr

1 Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the TFP-120 package. P

2 CAUTION Use an IC149-120-043-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-120 package IC socket on the user sy

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Board to User System WARNING Always switch OFF the user system and the

4 To connect the cable head to the user system, follow the instructions below. 2.1.1 Installing IC Socket After checking the location of pin 1 on th

5 2.1.4 Fastening IC Socket Connector CAUTION 1. Use the screwdriver provided for tightening screws. 2. The tightening torque must be 0.294 N•

6 User system interface boardUser systemPin 1Screws (M2 × 12 mm)with flat washers (for fastening cable head)IC socket (IC149-120-043-B51manufactured

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

7 2.2 Exchanging the Spacer of the Evaluation Chip Board While the user system interface board is connected to the user system, be careful not to ap

8 2.3 Connecting User System Interface Board to Evaluation Chip Board WARNING Observe the precautions listed below. Failure to do so will re

9 Connector No.UCN1 UCN1UCN2 UCN2User system interface boardEvaluation Chip Board Connector No.Board Connector No.Evaluation chip board Figure 4 Co

10 2.4 Recommended Dimensions for User System Mount Pad (Footprint) Figure 5 shows the recommended dimensions for the mount pad (footprint) for the

11 2.5 Dimensions for Evaluation Chip Board and User System Interface Board The dimensions for the evaluation chip board and the user system interfa

12 2.6 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board

13 2.7 Using the Emulator without Connecting User System WARNING Always switch OFF the user system and the emulator product before the USER S

14 P1SW1ONUSEROFF Figure 8 SW1 Jumper Socket Spacer(2.6MQ x 16 mm) Figure 9 Attaching Spacers

15 Section 3 User System Interface Circuits The following user interface circuits are required for the emulator when the user system interface boar

16 P23P27P23P27SN74CB3Q3306ASN74CB3Q3306AMCUUser system Figure 11 User System Interface Circuit (2) MCUUser system Sub-MCUP14P14SN74CB3Q3306ATXD SN

H8SX/1653 Group E6000H TFP-120User System Interface BoardHS1653ECN61H User’s ManualUser’s Manual Rev.2.00 2005.12Renesas Microcomputer Development E

17 MCUVHC244UHC14_RESVccUser systemEPM7128EPM7128_RES47 kΩ Figure 13 User System Interface Circuit (4)

18 Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H Emulator User's Manual

19  To use the crystal oscillator mounted on the evaluation chip board Install the crystal oscillator into the crystal oscillator terminals on the

20 Section 5 Notice 1. Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. 2. Do not apply exces

21 8. When this emulator is used without connecting to the user system, ensure that the SW1 jumper pin is inserted to [OFF]. Failure to do so will d

22 Section 6 Restrictions There are the following restrictions on emulation of the H8SX/1653 group when the user system interface board is connecte

Renesas Microcomputer Development Environment System User's Manual H8SX/1653 Group E6000H TFP-120User

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japanhttp://www.renesas.comRefer to

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanH8SX/1653 Group E6000H TFP-120User System Interface BoardREJ10B0200-0200HS1653EC

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the cus

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy

II LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and f

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,